REBUILT BOU-MATIC 1.5" FR3A HEAD W/OILER
Rebuilt Bou-Matic 1.5" FR3A Vacuum Pump Head with Oiler
Professionally rebuilt Bou-Matic FR3A dairy vacuum pump head with 1.5" connection and oiler. The FR3A is a compact rotary-vane vacuum pump commonly used in dairy barns, pipeline milking systems, and smaller milking installations that require dependable, continuous vacuum.
This pump-head-only configuration is a practical choice when the existing motor, mounting stand, pulley system, and other vacuum-system components are still serviceable and only the primary vacuum pump needs to be replaced.
Bou-Matic FR3A Specifications
- Pump: Bou-Matic FR3A
- Connection Size: 1.5"
- HP Rating: 3 HP
- Pump Speed: Approximately 1500 RPM
- Vacuum Capacity: Approximately 30 CFM
- Pump Shaft Diameter: 28 mm
- Configuration: Rebuilt pump head with oiler
- SKU: 40200
Professionally Rebuilt
Parts Department rebuilt vacuum pumps are thoroughly serviced before being offered for sale. Critical wear areas are inspected and corrected to help restore reliable vacuum performance.
- Rotor clearance reset as required
- Pump housing honed
- End plates resurfaced
- New vanes installed
- New bearings installed
- New shaft seals installed
- Oil lines, drippers, and filters replaced where applicable
- Pump tested after rebuilding to verify proper operation
Rebuilt pump assemblies include a 3-month warranty.
What Is Included
This listing is for the rebuilt Bou-Matic FR3A pump head with oiler.
This is not a complete motor-and-stand package. Motor, stand, pulley system, belts, reclaimer, and other installation components are not included unless specifically stated elsewhere in the listing.
Designed for Dairy Vacuum Systems
The Bou-Matic FR3A is an oil-lubricated rotary-vane vacuum pump designed for the continuous vacuum demands of dairy milking equipment. In its standard 3 HP configuration, the FR3A operates at approximately 1500 RPM and provides approximately 30 CFM of vacuum capacity.
Proper vacuum-pump sizing depends on the complete dairy system, including the number of milking units, pipeline layout, reserve requirements, regulators, receivers, and other equipment connected to the vacuum system.
If you are replacing a different pump or changing motor or pulley sizes, contact Parts Department so we can help confirm that the FR3A is appropriate for your installation.
Rebuilt Equipment Note
This is professionally rebuilt Bou-Matic equipment. Because rebuilt pumps use serviceable original components, cosmetic appearance may vary from one unit to another.
Paint finish, oiler appearance, fittings, and other non-critical visual details may vary. The important specifications are the Bou-Matic FR3A pump model, 1.5" configuration, 28 mm shaft, rebuilt condition, and included oiler described in this listing.
Related Bou-Matic FR3A Service Parts
Parts Department carries replacement components for maintaining and servicing Bou-Matic FR3 and FR3A vacuum pumps.
- Vanes for Bou-Matic FR3/FR3A Vacuum Pump – 4/Set – SKU 948323
- Bearing for Bou-Matic FR3/FR3A Vacuum Pump – SKU 90011
- Oil Seal for Bou-Matic FR3/3A/4/4A – SKU 9003
- Bou-Matic FR3/FR4 Oiler Kit – SKU FROIL
View all Vacuum Pump Repair Parts »
Other Bou-Matic Vacuum Pump Options
Parts Department also offers other rebuilt Bou-Matic vacuum pump heads for systems that require additional capacity or a different pump configuration.
- Rebuilt Bou-Matic 1.5" FR4 Vacuum Pump Head with Oiler
- Rebuilt Bou-Matic 2" FR4A Vacuum Pump Head with Oiler
- Rebuilt Bou-Matic DB-2000 Vacuum Pump Head with Oiler
Need Help Choosing the Correct Vacuum Pump?
Contact Parts Department at 800-245-8222 for assistance with Bou-Matic FR3A vacuum pumps, replacement parts, pulley sizing, or dairy vacuum-system setup. If you are replacing an existing pump, having the pump model, motor horsepower, shaft size, and a photo of the installation available can help us confirm the correct replacement.